mirror of
https://github.com/owntone/owntone-server.git
synced 2024-12-29 08:33:23 -05:00
93 lines
2.7 KiB
Markdown
93 lines
2.7 KiB
Markdown
# forked-daapd and Pulseaudio
|
|
Credit: [Rob Pope](http://robpope.co.uk/blog/post/setting-up-forked-daapd-with-bluetooth)
|
|
|
|
This guide was written based on headless Debian Jessie platforms. Most of the
|
|
instructions will require that you are root.
|
|
|
|
|
|
## Step 1: Setting up Pulseaudio in system mode with Bluetooth support
|
|
|
|
If you see a "Connection refused" error when starting forked-daapd, then you
|
|
will probably need to setup Pulseaudio to run in system mode [1]. This means
|
|
that the Pulseaudio daemon will be started during boot and be available to all
|
|
users.
|
|
|
|
How to start Pulseaudio depends on your distribution, but in many cases you will
|
|
need to add a pulseaudio.service file to /etc/systemd/system with the following
|
|
content:
|
|
|
|
```
|
|
# systemd service file for Pulseaudio running in system mode
|
|
[Unit]
|
|
Description=Pulseaudio sound server
|
|
Before=sound.target
|
|
|
|
[Service]
|
|
ExecStart=/usr/bin/pulseaudio --system --disallow-exit
|
|
|
|
[Install]
|
|
WantedBy=multi-user.target
|
|
```
|
|
|
|
If you want Bluetooth support, you must also configure Pulseaudio to load the
|
|
Bluetooth module. First install it (Debian:
|
|
`apt install pulseaudio-module-bluetooth`) and then add the following to
|
|
/etc/pulse/system.pa:
|
|
|
|
```
|
|
### Enable Bluetooth
|
|
.ifexists module-bluetooth-discover.so
|
|
load-module module-bluetooth-discover
|
|
.endif
|
|
```
|
|
|
|
Now you need to make sure that Pulseaudio can communicate with the Bluetooth
|
|
daemon through D-Bus. On Raspbian this is already enabled, and you can skip this
|
|
step. Otherwise do one of the following:
|
|
|
|
1. Add the pulse user to the bluetooth group: `adduser pulse bluetooth`
|
|
2. Edit /etc/dbus-1/system.d/bluetooth.conf and change the policy for
|
|
\<policy context="default"\> to "allow"
|
|
|
|
Phew, almost done with Pulseaudio! Now you should:
|
|
1. enable system mode on boot with `systemctl enable pulseaudio`
|
|
2. reboot (or at least restart dbus and pulseaudio)
|
|
3. check that the Bluetooth module is loaded with `pactl list modules short`
|
|
|
|
|
|
## Step 2: Setting up forked-daapd
|
|
|
|
Add the user forked-daapd is running as (typically "daapd") to the
|
|
"pulse-access" group:
|
|
|
|
```
|
|
adduser daapd pulse-access
|
|
```
|
|
|
|
Now (re)start forked-daapd.
|
|
|
|
|
|
## Step 3: Adding a Bluetooth device
|
|
|
|
To connect with the device, run `bluetoothctl` and then:
|
|
|
|
```
|
|
power on
|
|
agent on
|
|
scan on
|
|
**Note MAC address of BT Speaker**
|
|
pair [MAC address]
|
|
**Type Pin if prompted**
|
|
trust [MAC address]
|
|
connect [MAC address]
|
|
```
|
|
|
|
Now the speaker should appear in forked-daapd. You can also verify that
|
|
Pulseaudio has detected the speaker with `pactl list sinks short`.
|
|
|
|
---
|
|
|
|
[1] Note that Pulseaudio will warn against system mode. However, in this use
|
|
case it is actually the solution recommended by the [Pulseaudio folks themselves](https://lists.freedesktop.org/archives/pulseaudio-discuss/2016-August/026823.html).
|
|
|