mirror of
https://github.com/scottlamb/moonfire-nvr.git
synced 2024-12-27 15:45:55 -05:00
106 lines
4.7 KiB
Markdown
106 lines
4.7 KiB
Markdown
# Building and installing Moonfire NVR using provided scripts
|
|
|
|
This guide will walk you through building and installing Moonfire NVR with the
|
|
provided scripts. You should have already downloaded the source code as
|
|
mentioned in [install.md](install.md), and after completing these instructions
|
|
you should go back to that page to complete configuration.
|
|
|
|
There are no binary packages of Moonfire NVR available yet, so it must be built
|
|
from source. This is made easy using a few scripts that will do the job for you
|
|
unless you have very a different operating system. The scripts are written and
|
|
tested under ubuntu and raspbian but should not be hard to modify if necessary.
|
|
|
|
## Setting everything up
|
|
|
|
Start by executing the setup script:
|
|
|
|
$ cd moonfire-nvr
|
|
$ scripts/setup-ubuntu.sh
|
|
|
|
If this is the very first time you run this script, a file named `prep.config`
|
|
will be created and the script will stop. This file is where you will set
|
|
or change variables that describe the Moonfire installation you want. The
|
|
initial execution will put default values in this value, but only for the
|
|
most commonly changed variables. For a full list of variables, see below.
|
|
|
|
Once you modify this file (if desired), you run the setup script again. This
|
|
time it will use the values in the file and proceed with the setup.
|
|
The script will download and install any pre-requisites. Watch carefully for
|
|
error messages. It may be you have conflicting installations. If that is the
|
|
case you must either resolve those first, or go the manual route.
|
|
|
|
The script may be given the `-f` option. If you do, you are telling the script
|
|
that you do not want any existing installation of ffmpeg to be overwritten with
|
|
a newer one. This could be important to you. If you do use it, and the version
|
|
you have installed is not compatible with Moonfire, you will be told through
|
|
a message. If you have no ffmpeg installed, the option is effectively ignored
|
|
and the necessary version of ffmpeg will be installed.
|
|
|
|
The setup script should only need to be run once (after `prep.config` has been
|
|
created), although if you do a re-install of Moonfire, in particular a much
|
|
newer version, it is a good idea to run it again as requirements and pre-requisites
|
|
may have changed. Running the script multiple times should not have any negative effects.
|
|
|
|
*Note:* It is quite possible that during the running of the setup script,
|
|
in particular during the building of libavutil you will see several compiler
|
|
warnings. This, while undesirable, is a direct result of the original
|
|
developers not cleaning up the cause(s) of these warnings. They are, however,
|
|
just warnings and will not affect correct functioning of Moonfire.
|
|
|
|
Once the setup is complete, two steps remain: building and then installing.
|
|
There is a script for each of these scenarios, but since generally you would
|
|
want to install after a succesul build, the build script automatically invokes
|
|
the install script, unless specifically told not to.
|
|
|
|
## Building
|
|
|
|
The build script is involved like this:
|
|
|
|
$ scripts/build.sh
|
|
|
|
This script will perform all steps necessary to build a complete Moonfire
|
|
setup. If there are no build errors, this script will then automatically
|
|
invoke the install script (see below).
|
|
|
|
There are two options you may pass to this script. The first is `-B` which
|
|
means "build only". In other words, this will stop the automatic invocation
|
|
of the install script. The other option available is `-t` and causes the
|
|
script to ignore the results of any tests. In other words, even if tests
|
|
fail, the build phase will be considered successful. This can occasionally
|
|
be useful if you are doing development, and have temporarily broken one
|
|
or more test, but want to proceed anyway.
|
|
|
|
## Installing
|
|
|
|
The install step is performed by the script that can be manually invoked
|
|
like this:
|
|
|
|
$ scripts/install.sh
|
|
|
|
This script will copy various files resulting from the build to the correct
|
|
locations. It will also create a "service configuration" for systemctl that
|
|
can be used to control Moonfire. This service configuration can be prevented
|
|
by using the `-s` option to this script. It will also prevent the automatic
|
|
start of this configuration.
|
|
|
|
## Configuration variables
|
|
|
|
Although not all listed in the default `prep.config` file, these are the
|
|
available configuration variable and their defaults.
|
|
|
|
NVR_USER=moonfire-nvr
|
|
NVR_GROUP=$NVR_USER
|
|
NVR_PORT=8080
|
|
NVR_HOME_BASE=/var/lib
|
|
DB_NAME=db
|
|
DB_DIR=$NVR_HOME/$DB_NAME
|
|
SERVICE_NAME=moonfire-nvr
|
|
SERVICE_DESC="Moonfire NVR"
|
|
SERVICE_BIN=/usr/local/bin/$SERVICE_NAME
|
|
|
|
## Completing installation
|
|
|
|
After the steps on this page, go back to [Downloading, installing, and
|
|
configuring Moonfire NVR](install.md) to set up the sample file directory and
|
|
configure the system.
|