# ALSA ALSA is one of the main output configuration options for local audio; when using ALSA you will typically let the system select the sound card on your machine as the `default` device/sound card - a mixer associated with the ALSA device is used for volume control. However if your machine has multiple sound cards and your system chooses the wrong playback device, you will need to manually select the card and mixer to complete the OwnTone configuration. ## Quick introduction to ALSA devices ALSA devices can be addressed in a number ways but traditionally we have referred to them using the hardware prefix, card number and optionally device number with something like `hw:0` or `hw:0,1`. In ALSA configuration terms `card X, device Y` is known as `hw:X,Y`. ALSA has other _prefixes_ for each card and most importantly `plughw`. The `plughw` performs transparent sample format and sample rate conversions and maybe a better choice for many users rather than `hw:` which would fail when provided unsupported audio formats/sample rates. Alternative ALSA names can be used to refer to physical ALSA devices and can be useful in a number of ways: * more descriptive rather than being a card number * consistent for USB numeration - USB ALSA devices may not have the same card number across reboots/reconnects The ALSA device information required for configuration the server can be determined using `aplay`, as described in the rest of this document, but OwnTone can also assist; when configured to log at `INFO` level the following information is provided during startup: ```shell laudio: Available ALSA playback mixer(s) on hw:0 CARD=Intel (HDA Intel): 'Master' 'Headphone' 'Speaker' 'PCM' 'Mic' 'Beep' laudio: Available ALSA playback mixer(s) on hw:1 CARD=E30 (E30): 'E30 ' laudio: Available ALSA playback mixer(s) on hw:2 CARD=Seri (Plantronics Blackwire 3210 Seri): 'Sidetone' 'Headset' ``` The `CARD=` string is the alternate ALSA name for the device and can be used in place of the traditional `hw:x` name. On this machine the server reports that it can see the onboard HDA Intel sound card and two additional sound cards: a Topping E30 DAC and a Plantronics Headset which are both USB devices. We can address the first ALSA device as `hw:0` or `hw:CARD=Intel` or `hw:Intel` or `plughw:Intel`, the second ALSA device as `hw:1` or `hw:E30` and so forth. The latter 2 devices being on USB will mean that `hw:1` may not always refer to `hw:E30` and thus in such a case using the alternate name is useful. ## Configuring the server OwnTone can support a single ALSA device or multiple ALSA devices. ```conf # example audio section for server for a single sound card audio { nickname = "Computer" type = "alsa" card = "hw:1" # defaults to 'default' mixer = "Analogue" # defaults to 'PCM' or 'Master' mixer_device = "hw:1" # defaults to same as 'card' value } ``` Multiple devices can be made available to OwnTone using separate `alsa { .. }` sections. ```conf audio { type = "alsa" } alsa "hw:1" { nickname = "Computer" mixer = "Analogue" mixer_device = "hw:1" } alsa "hw:2" { nickname = "Second ALSA device" } ``` NB: When introducing `alsa { .. }` section(s) the ALSA specific configuration in the `audio { .. }` section will be ignored. If there is only one sound card, verify if the `default` sound device is correct for playback, we will use the `aplay` utility. ```shell # generate some audio if you don't have a wav file to hand sox -n -c 2 -r 44100 -b 16 -C 128 /tmp/sine441.wav synth 30 sin 500-100 fade h 0.2 30 0.2 aplay -Ddefault /tmp/sine441.wav ``` If you can hear music played then you are good to use `default` for the server configuration. If you can not hear anything from the `aplay` firstly verify (using `alsamixer`) that the sound card is not muted. If the card is not muted AND there is no sound you can try the options below to determine the card and mixer for configuring the server. ## Automatically Determine ALL relevant the sound card information As shown above, OwnTone can help, consider the information that logged: ```log laudio: Available ALSA playback mixer(s) on hw:0 CARD=Intel (HDA Intel): 'Master' 'Headphone' 'Speaker' 'PCM' 'Mic' 'Beep' laudio: Available ALSA playback mixer(s) on hw:1 CARD=E30 (E30): 'E30 ' laudio: Available ALSA playback mixer(s) on hw:2 CARD=Seri (Plantronics Blackwire 3210 Seri): 'Sidetone' 'Headset' ``` Using the information above, we can see 3 sound cards that we could use with OwnTone with the first sound card having a number of separate mixer devices (volume control) for headphone and the internal speakers - we'll configure the server to use both these and also the E30 device. The server configuration for these multiple outputs would be: ```conf # using ALSA device alias where possible alsa "hw:Intel" { nickname = "Computer - Speaker" mixer = "Speaker" } alsa "hw:Intel" { nickname = "Computer - Headphones" mixer = "Headphone" } alsa "plughw:E30" { # this E30 device only support S32_LE so we can use the 'plughw' prefix to # add transparent conversion support of more common S16/S24_LE formats nickname = "E30 DAC" mixer = "E30 " mixer_device = "hw:E30" } ``` NB: it is troublesome to use `hw` or `plughw` ALSA addressing when running OwnTone on a machine with `pulseaudio` and if you wish to use refer to ALSA devices directly that you stop `pulseaudio`. ## Manually Determining the sound cards you have / ALSA can see The example below is how I determined the correct sound card and mixer values for a Raspberry Pi that has an additional DAC card (hat) mounted. Of course using the log output from the server would have given the same results. Use `aplay -l` to list all the sound cards and their order as known to the system - you can have multiple `card X, device Y` entries; some cards can also have multiple playback devices such as the RPI's onboard sound card which feeds both headphone (card 0, device 0) and HDMI (card 0, device 1). ```shell $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: ALSA [bcm2835 ALSA], device 0: bcm2835 ALSA [bcm2835 ALSA] Subdevices: 6/7 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 Subdevice #2: subdevice #2 Subdevice #3: subdevice #3 Subdevice #4: subdevice #4 Subdevice #5: subdevice #5 Subdevice #6: subdevice #6 card 0: ALSA [bcm2835 ALSA], device 1: bcm2835 ALSA [bcm2835 IEC958/HDMI] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: IQaudIODAC [IQaudIODAC], device 0: IQaudIO DAC HiFi pcm512x-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 ``` On this machine we see the second sound card installed, an IQaudIODAC dac hat, and identified as `card 1 device 0`. This is the playback device we want to be used by the server. `hw:1,0` is the IQaudIODAC that we want to use - we verify audible playback through that sound card using `aplay -Dhw:1 /tmp/sine441.wav`. If the card has only one device, we can simply refer to the sound card using `hw:X` so in this case where the IQaudIODAC only has one device, we can refer to this card as `hw:1` or `hw:1,0`. Use `aplay -L` to get more information about the PCM devices defined on the system. ```shell $ aplay -L null Discard all samples (playback) or generate zero samples (capture) default:CARD=ALSA bcm2835 ALSA, bcm2835 ALSA Default Audio Device sysdefault:CARD=ALSA bcm2835 ALSA, bcm2835 ALSA Default Audio Device dmix:CARD=ALSA,DEV=0 bcm2835 ALSA, bcm2835 ALSA Direct sample mixing device dmix:CARD=ALSA,DEV=1 bcm2835 ALSA, bcm2835 IEC958/HDMI Direct sample mixing device dsnoop:CARD=ALSA,DEV=0 bcm2835 ALSA, bcm2835 ALSA Direct sample snooping device dsnoop:CARD=ALSA,DEV=1 bcm2835 ALSA, bcm2835 IEC958/HDMI Direct sample snooping device hw:CARD=ALSA,DEV=0 bcm2835 ALSA, bcm2835 ALSA Direct hardware device without any conversions hw:CARD=ALSA,DEV=1 bcm2835 ALSA, bcm2835 IEC958/HDMI Direct hardware device without any conversions plughw:CARD=ALSA,DEV=0 bcm2835 ALSA, bcm2835 ALSA Hardware device with all software conversions plughw:CARD=ALSA,DEV=1 bcm2835 ALSA, bcm2835 IEC958/HDMI Hardware device with all software conversions default:CARD=IQaudIODAC IQaudIODAC, Default Audio Device sysdefault:CARD=IQaudIODAC IQaudIODAC, Default Audio Device dmix:CARD=IQaudIODAC,DEV=0 IQaudIODAC, Direct sample mixing device dsnoop:CARD=IQaudIODAC,DEV=0 IQaudIODAC, Direct sample snooping device hw:CARD=IQaudIODAC,DEV=0 IQaudIODAC, Direct hardware device without any conversions plughw:CARD=IQaudIODAC,DEV=0 IQaudIODAC, Hardware device with all software conversions ``` For the server configuration, we will use: ```conf audio { nickname = "Computer" type = "alsa" card="hw:1" # mixer=TBD # mixer_device=TBD } ``` ## Mixer name Once you have the card number (determined from `aplay -l`) we can inspect/confirm the name of the mixer that can be used for playback (it may NOT be `PCM` as expected by the server). In this example, the card `1` is of interest and thus we use `-c 1` with the following command: ```shell $ amixer -c 1 Simple mixer control 'DSP Program',0 Capabilities: enum Items: 'FIR interpolation with de-emphasis' 'Low latency IIR with de-emphasis' 'High attenuation with de-emphasis' 'Fixed process flow' 'Ringing-less low latency FIR' Item0: 'Ringing-less low latency FIR' Simple mixer control 'Analogue',0 Capabilities: pvolume Playback channels: Front Left - Front Right Limits: Playback 0 - 1 Mono: Front Left: Playback 1 [100%] [0.00dB] Front Right: Playback 1 [100%] [0.00dB] Simple mixer control 'Analogue Playback Boost',0 Capabilities: volume Playback channels: Front Left - Front Right Capture channels: Front Left - Front Right Limits: 0 - 1 Front Left: 0 [0%] [0.00dB] Front Right: 0 [0%] [0.00dB] ... ``` This card has multiple controls but we want to find a mixer control listed with a `pvolume` (playback) capability - in this case that mixer value required for the server configuration is called `Analogue`. For the server configuration, we will use: ```conf audio { nickname = "Computer" type = "alsa" card="hw:1" mixer="Analogue" # mixer_device=TBD } ``` ## Mixer device This is the name of the underlying physical device used for the mixer - it is typically the same value as the value of `card` in which case a value is not required by the server configuration. An example of when you want to change explicitly configure this is if you need to use a `dmix` device (see below). ## Handling Devices that cannot concurrently play multiple audio streams Some devices such as various RPI DAC boards (IQaudio DAC, Allo Boss DAC...) cannot have multiple streams opened at the same time/cannot play multiple sound files at the same time. This results in `Device or resource busy` errors. You can confirm if your sound card has this problem by using the example below once have determined the names/cards information as above. Using our `hw:1` device we try: ```shell # generate some audio $ sox -n -c 2 -r 44100 -b 16 -C 128 /tmp/sine441.wav synth 30 sin 500-100 fade h 0.2 30 0.2 # attempt to play 2 files at the same time $ aplay -v -Dhw:1 /tmp/sine441.wav & Playing WAVE '/tmp/sine441.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo Hardware PCM card 1 'IQaudIODAC' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 2 rate : 44100 exact rate : 44100 (44100/1) msbits : 16 buffer_size : 22052 period_size : 5513 period_time : 125011 tstamp_mode : NONE tstamp_type : MONOTONIC period_step : 1 avail_min : 5513 period_event : 0 start_threshold : 22052 stop_threshold : 22052 silence_threshold: 0 silence_size : 0 boundary : 1445199872 appl_ptr : 0 hw_ptr : 0 $ aplay -v -Dhw:1 /tmp/sine441.wav aplay: main:788: audio open error: Device or resource busy ``` In this instance this device cannot open multiple streams - OwnTone can handle this situation transparently with some audio being truncated from the end of the current file as the server prepares to play the following track. If this handling is causing you problems you may wish to use [ALSA's `dmix` functionally](https://www.alsa-project.org/main/index.php/Asoundrc#Software_mixing) which provides a software mixing module. We will need to define a `dmix` component and configure the server to use that as it's sound card. The downside to the `dmix` approach will be the need to fix a sample rate (48000 being the default) for this software mixing module meaning any files that have a mismatched sample rate will be resampled. ## ALSA dmix configuration/setup A `dmix` device can be defined in `/etc/asound.conf` or `~/.asoundrc` for the same user running OwnTone. We will need to know the underlying physical sound card to be used: in our examples above, `hw:1,0` / `card 1, device 0` representing our IQaudIODAC as per output of `aplay -l`. We also take the `buffer_size` and `period_size` from the output of playing a sound file via `aplay -v`. ```conf # use 'dac' as the name of the device: "aplay -Ddac ...." pcm.!dac { type plug slave.pcm "dmixer" hint.description "IQAudio DAC s/w dmix enabled device" } pcm.dmixer { type dmix ipc_key 1024 # need to be uniq value ipc_key_add_uid false # multiple concurrent different users ipc_perm 0666 # multi-user sharing permissions slave { pcm "hw:1,0" # points at the underlying device - could also simply be hw:1 period_time 0 period_size 4096 # from the output of aplay -v buffer_size 22052 # from the output of aplay -v rate 44100 # locked in sample rate for resampling on dmix device } hint.description "IQAudio DAC s/w dmix device" } ctl.dmixer { type hw card 1 # underlying device device 0 } ``` Running `aplay -L` we will see our newly defined devices `dac` and `dmixer` ```shell $ aplay -L null Discard all samples (playback) or generate zero samples (capture) dac IQAudio DAC s/w dmix enabled device dmixer IQAudio DAC s/w dmix device default:CARD=ALSA bcm2835 ALSA, bcm2835 ALSA Default Audio Device ... ``` At this point we are able to rerun the concurrent `aplay` commands (adding `-Ddac` to specify the playback device to use) to verify ALSA configuration. If there is only one card on the machine you may use `pcm.!default` instead of `pcm.!dac` - there is less configuration to be done later since many ALSA applications will use the device called `default` by default. Furthermore on RPI you can explicitly disable the onboard sound card to leave us with only the IQaudIODAC board enabled (won't affect HDMI sound output) by commenting out `#dtparam=audio=on` in `/boot/config.txt` and rebooting. ### Config with dmix We will use the newly defined card named `dac` which uses the underlying `hw:1` device as per `/etc/asound.conf` or `~/.asoundrc` configuration. Note that the `mixer_device` is now required and must refer to the real device (see the `slave.pcm` value) and not the named device (ie `dac`) that we created and are using for the `card` configuration value. For the final server configuration, we will use: ```conf audio { nickname = "Computer" type = "alsa" card="dac" mixer="Analogue" mixer_device="hw:1" } ``` ## Setting up an Audio Equalizer There exists an ALSA equalizer plugin. On `debian` (incl Raspberry Pi) systems you can install this plugin by `apt install libasound2-plugin-equal`; this is not currently available on Fedora (FC31) but can be easily built from [source](https://github.com/raedwulf/alsaequal) after installing the dependant `ladspa` package. Once installed the user must setup a virtual device and use this device in the server configuration. If you wish to use your `hw:0` device for output: ```conf # /etc/asound.conf ctl.equal { type equal; # library /usr/lib64/ladspa/caps.so } pcm.equal { type plug; slave.pcm { type equal; ## must be plughw:x,y and not hw:x,y slave.pcm "plughw:0,0"; # library /usr/lib64/ladspa/caps.so } hint.description "equalised device" } ``` and in `owntone.conf` ```conf alsa "equal" { nickname = "Equalised Output" # adjust accordingly for mixer with pvolume capability mixer = "PCM" mixer_device = "hw:0" } ``` Using the web UI and on the outputs selection you should see an output called `Equalised Output` which you should select and set the volume. When starting playback for any audio tracks you should hopefully hear the output. In a terminal, run `alsamixer -Dequal` and you'll see the eqaliser - to test that this is all working, go and drop the upper frequencies and boosting the bass frequencies and give it a second - if this changes the sound profile from your speakers, well done, its done and you can adjust the equalizer as you desire. Note however, the equalizer appears to require a `plughw` device which means you cannnot use this equalizer with a `dmix` output chain. ## Troubleshooting * Errors in log `Failed to open configured mixer element` when selecting output device * Errors in log `Invalid CTL` or `Failed to attach mixer` when playing/adjusting volume `mixer` value is wrong. Verify name of `mixer` value in server config against the names from all devices capable of playback using `amixer -c `. Assume the device is card 1: ```shell (IFS=$'\n' CARD=1 for i in $(amixer -c ${CARD} scontrols | awk -F\' '{ print $2 }'); do amixer -c ${CARD} sget "$i" | grep Capabilities | grep -q pvolume && echo $i done ) ``` Look at the names output and choose the one that fits. The outputs can be something like: ```shell # laptop Master Headphone Speaker PCM Mic Beep # RPI with no additional DAC, card = 0 PCM # RPI with additional DAC hat (IQAudioDAC, using a pcm512x chip) Analogue Digital ``` * No sound during playback - valid mixer/verified by aplay Check that the mixer is not muted or volume set to 0. Using the value of `mixer` as per server config and unmute or set volume to max. Assume the device is card 1 and `mixer = Analogue`: ```shell amixer -c 1 set Analogue unmute ## some mixers can not be muted resulting in "invalid command" amixer -c 1 set Analogue 100% ``` An example of a device with volume turned all the way down - notice the `Playback` values are `0`[0%]`: ```shell Simple mixer control 'Analogue',0 Capabilities: pvolume Playback channels: Front Left - Front Right Limits: Playback 0 - 1 Mono: Front Left: Playback 0 [0%] [-6.00dB] Front Right: Playback 0 [0%] [-6.00dB] ``` * Server stops playing after moving to new track in paly queue, Error in log `Could not open playback device` The log contains these log lines: ```log [2019-06-19 20:52:51] [ LOG] laudio: open '/dev/snd/pcmC0D0p' failed (-16)[2019-06-19 20:52:51] [ LOG] laudio: Could not open playback device: Device or resource busy [2019-06-19 20:52:51] [ LOG] laudio: Device 'hw' does not support quality (48000/16/2), falling back to default [2019-06-19 20:52:51] [ LOG] laudio: open '/dev/snd/pcmC0D0p' failed (-16)[2019-06-19 20:52:51] [ LOG] laudio: Could not open playback device: Device or resource busy [2019-06-19 20:52:51] [ LOG] laudio: ALSA device failed setting fallback quality[2019-06-19 20:52:51] [ LOG] player: The ALSA device 'Computer' FAILED ``` If you have a RPI with a DAC hat with a `pcm512x` chip will affect you. This is because the server wants to open the audio device for the next audio track whilst current track is still playing but the hardware does not allow this - see the comments above regarding determining concurrrent playback. This error will occur for output hardware that do not support concurrent device open and the server plays 2 files of different bitrate (44.1khz and 48khz) back to back. If you observe the error, you will need to use the `dmix` configuration as mentioned above.